Floor Loop Detectors for High-Speed Door Activation
Floor loop detectors sense vehicles at ground level and send an activation signal to a high-speed door’s controller. They let forklifts, vans and other vehicles request access without a driver pressing a button.
However, opening the door and protecting the doorway are different jobs. The right setup needs suitable detection, correctly configured controls and separate safeguards for people and vehicles.
Understanding that signal path makes it easier to compare a conventional in-ground loop with a wireless detector and a magnetic probe.
How floor loop detectors activate a door
A conventional system has three main parts: a wire loop in the floor, a detector module and a connection to the door control panel.
The vehicle changes the loop’s electrical behaviour
Alternating current flowing through the loop creates a magnetic field. When a vehicle passes over it, the vehicle’s metal structure and other metallic objects change the loop’s inductance.
The detector monitors that change through its sensing circuit. As the Federal Highway Administration’s vehicle-sensing explanation describes, loop inductance determines an oscillator’s frequency. A change allows the electronics to recognise vehicle arrival or passage.
The loop detects the vehicle’s effect on the field. It doesn’t depend on tyre pressure or a driver touching a control.

The detector signals the controller
The module operates an output relay when detection meets its configured conditions. That relay forwards the vehicle signal to the high-speed door, gate or barrier controller.
The controller then follows its programmed sequence. It may open the entrance, maintain an opening request or prevent closing while an occupied signal remains active.
The detector doesn’t directly drive the door motor. Closing behaviour still depends on the controller, operating mode and protective devices.
Where loops fit at high-speed doors
Induction loops suit defined vehicle routes in production buildings, manufacturing facilities and logistics sites. They support hands-free vehicle entry and access control at fixed openings where vehicles repeatedly follow the same approach.
Because the sensing loop sits in the floor, heavy rain or snow doesn’t obscure its view as it could with an optical device. Correctly installed loops can therefore provide reliable detection in those conditions.
Placement must still match the route. An approach loop should detect the intended traffic early enough for the opening sequence, without reacting unnecessarily to vehicles travelling past.

Our high-speed door installation service covers industrial and commercial premises. Activation needs to suit vehicle direction, available approach space and pedestrian access.
Some sites also pair a rapid door with a separate security shutter. Each door has a different purpose, so their controls must work together without creating conflicting movements.
Presence mode and exit mode serve different jobs
A detector’s operating mode matters as much as its sensing technology. An opening pulse and a continuous occupied signal aren’t interchangeable.
Exit mode requests an opening
An exit-mode device detects an approaching or departing vehicle and sends an opening request. This suits a controlled exit where vehicles need to leave without using a remote or push button.
However, that request doesn’t establish that the doorway remains occupied. Once the opening signal ends, the controller relies on its remaining inputs and programmed sequence.
Presence mode reports occupancy
A presence-capable detector, also called a vehicle presence sensor, maintains an output while it detects a vehicle within its detection zone. The controller can use that signal to hold an entrance open or inhibit closing.
AES offers e-Loop kits with different exit and presence functions. The selected kit must match the required behaviour.
A vehicle-presence signal only covers the detector’s vehicle-detection zone. It doesn’t prove that a pedestrian or the whole doorway is clear.
A longer hold-open timer also can’t replace protective detection.
Choosing wireless and probe-based detectors
Several products sold alongside ground loops use different detection methods. Choose by function and site conditions rather than treating every vehicle sensor as the same component.
AES e-Loop offers wireless vehicle activation
AES describes its e-Loop exit device as suitable for all vehicle types, including motorbikes. Its wireless arrangement reduces the need for conventional loop installation and is intended to keep setup time low.
Presence-mode and exit-mode kits serve different control requirements. Kits are also offered with and without LCD transceivers, so those descriptions identify different package options rather than one universal specification.
The AES Diagnostic Remote is a separate commissioning and maintenance tool. It gives installers wireless diagnostics for e-Loop systems, which helps distinguish sensing or communication issues during investigation.
Diablo Mini Loop provides an opening pulse
The Diablo Mini Loop responds when a ferrous object approaches its probe and produces an opening pulse.
Its wiring involves control-panel power and safety-input connections, with a two-core cable linking the probe. Those connections need to suit the complete control arrangement.
The important limitation is explicit: Diablo Mini Loop sensors cannot provide presence detection, according to the product description.
That makes the Mini Loop an opening-trigger option rather than a substitute for an occupied-zone detector. Using a panel input labelled for safety doesn’t change the probe’s detection capability.
When a Magna sensor is suitable
Magna sensors detect changes in ambient magnetic fields. They use a different principle from a conventional alternating-current induction loop.
The sensor is fully waterproof and can sit in any orientation. It also resets at each power-up, allowing relocation and recommissioning rather than requiring one permanent orientation.
However, the surrounding structure restricts its use. Magna sensors must not sit inside a steel-framed building or within 0.5m of an iron manhole cover, drain or other large ferrous mass.
Those restrictions matter at industrial entrances, where steel columns, drainage channels and reinforced structures may surround the approach.
The product information describes an angled protective hole for the sensor. A 20mm drill bit is just large enough for that arrangement, which protects the sensor and helps accommodate the cable bend.
These details apply when fitting Magna sensors. They aren’t general fitting instructions for every magnetic probe or floor loop.
Matching loop cable and detector modules
A conventional loop installation needs compatible cable and electronics. Buying only a detector PCB doesn’t provide the complete vehicle detection system.
Preformed loops and loose cable serve different needs
Preformed loop cables are available in 2m x 1m and 3m x 2m sizes. Each includes 15m of trailing cable for connection to the detector.
The preformed loop cable’s trailing section needs to reach the intended detector location. Its length is part of the layout decision, alongside the vehicle route and control-panel position.
AEI loop cable comes in 100m and 500m lengths. It’s flexible, rubber-insulated and flame-retardant, and is used for coil-end leads.
The FHWA’s loop detector electronics guidance describes the system as a tuned electrical circuit. The loop cable, connecting cable and detector must work as a compatible assembly.
Single-channel and dual-channel PCBs cover different arrangements
These Sensable modules provide different channel counts.
| Detector PCB | Supply | Channels |
|---|---|---|
| Sensable ULD466814 | 12/24V | Single |
| Sensable ULD466923 | 12-24V | Dual |
A dual-channel detector supports two loop channels, but it doesn’t automatically establish direction control or a particular door sequence. Those functions depend on the module’s capabilities and the controller arrangement.
Commission the whole entrance, not just the sensor
Successful vehicle detection is only one part of commissioning. The complete entrance system’s protective response must work throughout the vehicle’s passage and during abnormal conditions.
Test the actual traffic pattern
Commissioning should include the vehicles that use the route, their normal approach directions and situations where they stop or queue near the entrance.
The engineer should establish whether the detector sends an opening pulse or maintains an occupied output. Tests should then demonstrate the controller’s response when that signal starts and ends.
For wider layout decisions, our guide to choosing warehouse high-speed doors covers how activation fits the opening and daily traffic.
Include protection and fault behaviour
Photocells, safety edges, emergency stops and other installed safeguards need testing alongside activation. A working approach loop doesn’t demonstrate that those devices protect the threshold.
Maintenance should also cover cable condition, terminations, detector indications and the control panel. FHWA’s detector maintenance guidance treats loop-system fault investigation as a technical task.
Repeated false openings, missed vehicles or unexpected closing need professional attention. Don’t bypass protective inputs to keep traffic moving.
Key takeaways
- Conventional floor loops detect changes in inductance and signal the door controller through a detector module.
- Exit activation and presence detection require different output behaviour, so product names alone aren’t enough to select a system.
- Wireless e-Loop kits, Diablo probes and Magna sensors have different functions and installation restrictions.
- Commissioning must demonstrate both vehicle activation and the complete entrance’s protective response.
Frequently asked questions
What is a loop on the road or warehouse floor?
It’s usually a wire loop installed beneath the surface and connected to detection electronics. A visible rectangular cut may show its route.
At an industrial entrance, the loop detects vehicles at a chosen position. Similar technology supports road-traffic detection, gates and barriers, although each application uses its own control sequence.
Can a vehicle loop replace pedestrian safety sensors?
A vehicle loop cannot reliably provide pedestrian protection. Its purpose is to respond to the metal structure of vehicles within its detection area.
People walking through or standing near the opening still need suitable safeguards. The complete door system must address the hazards around the moving door, including areas outside the vehicle loop’s coverage.
Choose detection around your traffic
Reliable activation starts with the required behaviour: an opening request, a maintained vehicle-presence signal or a combination of inputs. The detector technology and installation must support that behaviour.
Keep activation and protection separate in the design, then test them together at the finished entrance.
For high-speed door servicing or repair support, Contact Us.
Discover more from UK Doors and Shutters
Subscribe to get the latest posts sent to your email.




Leave a Reply
Want to join the discussion?Feel free to contribute!